Posts categorized ME Archive

Creating a Secondary Mirror Support System (SMSS) for a secondary mirror in a space telescope.

A one or two sentence description of your project.

A mechanical drum player to provide handicapped children the ability to play the drums.

This project aims to manufacture a device capable of rapidly cycling phase change materials through a hot and a cold temperature cycle in order to determine their long term suitability for use in thermal batteries.

This is an interdisciplinary project between ECE and ME students. The teams designed and manufactured a rolling robot that uses linear actuators to move and navigate flat environments.

Physical experimentation is crucial to grasping a deeper understanding of fluid dynamics. Our team is working to provide the Mechanical Engineering department a solution via designing, analyzing, and building a transportable tow tank structure for students’ use.

Gas-powered automobiles negatively impact the earth because of pollution that is exhausted from their engines. This project implements a cheap, efficient, and electric-powered cart design to raise awareness on the power of efficient electric vehicles. 

A one or two sentence description of your project.

Several problems are being addressed with the project at hand. The main one, however, is a heavily discussed and often times argued about problem: global warming. As of 2019, there are over 276 million vehicles registered in the United States alone. Those carbon emissions add up quickly. If people want to increase the longevity of the earth and allow it to continue long enough to support their kids and grandkids, then it might be time to make a change. This change comes in the form of renewable resources and renewable energy, and that is exactly what the drill powered cart team plans to show throughout the project.

Tow Tank devices are used in testing boat and aerodynamic models for things like aerodynamic drag and lift. These devices typically cost around $20,000 which is the reason not every school has access to such a device. Here in the University of Rochester, we don’t have our own tow tank device, but we do have a swimming pool, and a passion for solving problems. In this post, we are showcasing our prototype for a tow tank that can be assembled and used in the gym swimming pool. The cost of the prototype and the completed final device is less than $1000!

The main goal of this project is to build, assemble, and successfully test an accelerated testing machine for the India Mark II. In the India Mark II pump, the water gaskets wore off frequently during the pumping of water and needed frequent replacement which proved costly. To counter the problem, the project below proposes an accelerated testing machine composed of a slider-crank mechanism. The mechanism incorporated a flywheel driven by a motor that ensures continuous harmonic motion that replicates pumping mechanisms in the field. The mechanism was designed, simulated and a finite element analysis carried out in CAD software. These are covered in the report along with testing results and recommendations provided for improvement of future designs.​

Modern mechanical engineers utilize computers but do not fully understand how the computer performs its computations. Understanding the fundamentals will give them a better understanding to the limitation of traditional computing. To address this gap between functionality and understanding, we built a 4ft by 6ft physical 3-bit adder to blow up the tiny processes that go on inside of a computer. Using a system of logic gates, where marbles act as inputs and outputs, our machine is able to add numbers 7 and below to each other and produce an output in binary.

Robotic control is becoming increasingly integral across many disciplines and industries. Understanding the fundamentals of robotic control evolves people’s way of life into a more convenient and efficient epoch. Here in University of Rochester, robotics courses enable students to have basic hand-on learning experience over robotic control systems. This robotic steering system team is aiming at designing an inexpensive but reliable, and easy to replicate solution which fits the needs to teach the robotics courses at University of Rochester.

Have you ever had a gourd and wanted it over there, but in a way that would inspire the masses? The Mechanical Engineering Department sure has, and has tasked our team with creating their submission to our ASME-hosted annual pumpkin launch.

The Pittsford Community Library Team was tasked to design and manufacture an interactive ball maze machine. Upon completion, the model will be moved and displayed within the children’s lofted play area of the Pittsford Community Library. The main goal of this project was to deliver a fully functioning ball maze display, decorated with laser cut wooden designs of landmarks across Rochester. Combining elements of STEM and history, the team hoped to create a fun and educational display that children, as well as all library visitors, can enjoy.

The Mary Cariola Classroom Aids project focused on developing LED light panels to refocus the attention of visually impaired students. Our solution includes 4 individual panels, as well as a stand that can rotate to three different angles to help accommodate various students.

Art and Engineering are two separate disciplines that don’t collaborate and intersect as much as they should. There are many mediums that mix both disciplines to allow for a fuller artistic approach to engineering, but these mediums aren’t abundant on the River Campus.
The Kinetic Sculpture capstone project aims to be the bridge between these departments through kinetic art. The following interactive art piece fuses the concepts of art and mechanics to provide students with a one-of-a-kind experience on campus.

With increasing concerns about the environmental impact of ground transportation, the industry needs alternative solutions that are safe, efficient, and environmentally friendly. One solution to the pollution problem is human-powered vehicles which emit zero greenhouse gas on the road. This project aims to implement a new material technology (fiberglass) into the design of a human-powered vehicle to make it more lightweight, functional, and safe. The test results concluded that fiberglass can indeed be used to manufacture the monocoque of a human-powered vehicle without compromises. The findings of this project will advance the engineering knowledge of fiberglass in this field and enable other engineering teams to use this technology in future designs.

Human-powered submarines are underwater vessels that are driven solely by the power of a human pilot. The Foundation for Underwater Research and Education (FURE) has put on the International Submarine Races (ISR) for several years. In the past, teams from around the world have traveled to the Naval Surface Warfare Center, Carderock Division to compete and race with their human-powered submarine designs. With an in-person event not possible this year, a virtual event (vISR) will be taking place instead. The Human Powered Submarine team set out to tackle specific design problems related to the hull, drivetrain, and propulsion system of a human-powered submarine in the spirit of the virtual event guidelines.

The Ground Support team was asked to make a new design for a safe aircraft interface mechanism for the Shipboard Aircraft Handler (SAH). The SAH is made to grab, lift and tow Naval fighter jets, like the F-15 or the F-35, while on the deck of a aircraft carrier. The current design is being tested by Naval Air Systems Command, Patuxent River Maryland

L3Harris Technologies is an American defense company that builds a variety of mechanical, optical, and electrical systems. The Rochester division designs and builds systems for space applications. Optical space telescopes are widely used in both Earth and astrophysical observations and play a major role in scientific and national security. For optical telescopes to function properly and take clear images, their optics must be precisely aligned to focus light. However, during the launch of the telescope, the relative positions of these optics can change. The goal of the project is to build a mechanism to finely adjust the position of these optics to enhance resolution and accuracy of the telescope images. This improved image quality has significant implications for both terrestrial and space observations with applications to scientific research and national security.

Our team, along with Drill Powered Carts A have built a fully functioning, energy-efficient, and sustainable vehicle, which will be powered by a single electric power drill. By doing this, each team hopes to not only show people that electric-powered transportation is possible, reliable, and easy but, whose cart is the best. The two teams will face off in an endurance race to see which cart can make the most laps around a race track at the University of Rochester River Campus. This will show which team has the most optimized mechanical design.

The goal of this project is to launch a non-spherical shape in a controlled, repeatable manner to study the impacts of low-velocity debris on the granular surfaces of asteroids. This research could potentially assist in future missions to land on asteroids by learning about the trajectories taken after initial impact and the effects that spin, angle of impact, and velocity have on those trajectories. ​

Several optomechanical applications have a need for a 360° kinematic mounting system capable of withstanding thermal loading due to heat generation from electronic devices. It is advantageous for optical systems to have a repeatable and controlled, known distance between devices such as optics, sensors, light sources, mirrors or assorted non-optical sensors. The team was able to design a thermally stable spaceframe solution, capable of reducing movement of any assembled components to minimal displacements on the order of microns.

Students at the Mary Cariola Center with visual impairments are attracted to light in rooms, often pulling their attention away from the teachers/lesson to look upwards at the ceiling lights. Lighted surfaces that provide contrast can help students focus on that surface and on any activity being performed on the lighted surface. The team was tasked with creating a mat suitable for children that illuminates in order to draw the student’s attention downward.

The Rossell Hope Robbins Library is underutilized by many students on campus due to the lack of awareness of the library and its resources. To promote awareness for the library, this project contains designs for a “life-size” portable chess set with medieval themes.

In Syria, there are thousands of refugees that have upper limb amputations that don’t have access to function prosthetics. Prosthesis for New Syria was founded by Omar Soufan and Ibrahim Mohammad to provide an affordable and functional prosthetic hand to these refugees. The goal of the design is to create a 3D printable prosthetic that improves on the design from the previous year by making the hand look more realistic as well as improve its functionality.

The project aims to design a steering system for robots used in various ECE courses. The robotic system has issues with lifetime, maneuverability, and mobility. The new model was designed with an aim to direct most of the off-axis load into the chassis while still maintaining the capability of the DC motor driving the wheel. These improvements helped in significantly increasing the lifetime of the motors. Additionally, the ability to steer each wheel independently increased the mobility of the robot.

The Children’s section at the Pittsford Community Library has three main spaces for play. While the two-spaces, located on the main level, are well defined and engaging for children with interactive elements, the project was to create a new interactive display for the third space located on the upper level.

Helmets in the NFL are not effective enough to safeguard the health of the players. Players sustain concussions which can not only bench them, but leave life-long brain damage from the accelerations experienced during impact. As part of the project to improve the helmet, simulations were used to test material properties of different components of football helmets, such as hard foams, soft foams, and the shell. Data from the simulations were analyzed with performance metrics provided by the NFL.